Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateFast, Reliable Garage Door Spring Repair Across Overland
If a spring just let go and your door won’t lift, call (844) 745-3717. A garage door spring repair in Overland typically costs $180 – $340 for one spring, and we’ll give you a written price before any work starts. We know this town: the tight mid-century driveways, the low garage headers, the heavy doors on detached workshops behind the house. Overland’s housing was mostly built between 1940 and 1970, so the springs we replace here are often the originals, not the second set. We answer 24/7, and fast dispatch from 7am to 7pm gets a local pro to your Overland door as soon as the schedule allows.
Why Overland Homeowners Call Florissant Garage Door Repair Pros for Garage Door Spring Repair
Springs are high-tension parts, and plenty of generalists won’t touch them. We do. Spring repair is a named service here, handled in-house, not subcontracted to whoever picks up the phone. Our technicians have up to 12 years of experience, and they know that a heavy door on an Overland workshop is usually a spring that stopped carrying its load, not an opener that suddenly quit.
We work on the door you have. That matters in Overland, where an original Clopay or Wayne Dalton door from the 1950s or 1960s won’t take a stock replacement spring without a weight check and a rating match. Because we’re factory-familiar with those brands, the diagnostic detour is shorter. One visit tells us which spring is right and whether it’s a one-trip job or a special order.
And we mean it about no replacement pitch. If a spring and cable will do, that’s what we quote. We serve Overland and the surrounding inner-ring suburbs, so when we say we’re familiar with the area, we’re talking about the low-clearance headers, the narrow drives, and the older brick bungalows with small single-car garages. Same-day and emergency service are real offerings here, not add-ons.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Our Garage Door Spring Repair Services in Overland
Torsion Spring Replacement
Torsion springs do the lifting on most Overland doors, mounted on the header above the opening. On a 1940s to 1960s garage, that header is often low, and the original spring was sized to a door weight nobody wrote down. We measure the door, rate the new spring to match, and wind it to spec. Torsion work is dangerous, so it belongs with a trained technician, not a homeowner with a winding bar and a video.

Broken Spring Repair
A snapped spring usually announces itself with a bang, then the door won’t come up, or comes up heavy and crooked. We find the break, check whether it took a cable or an end bearing plate with it, and get the door back in balance. If you’re searching for garage door spring repair in Overland, this is the call most homeowners are making.

Safety Cable Installation
Extension springs on older Overland doors should run through a safety cable that contains the spring if it breaks. Many mid-century installs skipped it. We add cables so a failed spring stays in its track instead of flying across the garage, which is exactly the kind of thing this older housing stock still needs.

Spring Adjustment
Sometimes the spring isn’t broken, just tired. A door that feels heavy or slams down is out of balance, and the opener is straining to do the spring’s job. We adjust or re-rate the spring so the door lifts with a hand’s pull, which takes the load off your opener and your door.
What Makes a Spring Job in Overland Different
Here’s the local wrinkle that a generic spring page won’t tell you. Overland’s mid-century garages frequently have low-clearance headers, so on streets like Lackland and Woodson a standard high-lift conversion simply won’t fit, and prosaic low-headroom torsion kits become a special order. That means a spring swap on these doors regularly needs a second visit for parts rather than a straight off-the-truck replacement. We tell you that up front so the timing doesn’t surprise you. The upside: we get the right spring for the actual header, the actual door weight, and the actual driveway, and the door lasts instead of failing early.
In Overland’s post-WWII single-car garages, a common call is a door that slammed down and now hangs heavy, usually an original torsion spring that finally gave out after decades of service, sometimes taking a cable or an end bearing plate with it. The door sits out of balance, the opener strains against a load the springs should carry, and the drums or cables need re-seating before the new spring goes on. Behind narrow driveways and low headers, that confirms the spring rating has to be wound to the door’s real weight instead of assuming a standard replacement will fit.
Then there are the detached workshops. Some Overland properties have an oversized or heavy door on the shop out back, and the homeowner blames the opener. Usually the spring no longer carries that weight, and the opener is just doing its best. Those doors need a heavier-duty spring, and we can set one up.
The climate doesn’t help. Overland sits in the humid continental Midwest, with hot, humid summers and cold winters that bring repeated freeze-thaw cycles and occasional ice storms. Those swings are hard on springs, cables, and weather seals, and seasonal failures spike in late winter when the ground thaws and doors that swelled in summer start binding.
Common Garage Door Spring Repair Problems We See in Overland Homes
- Original springs at the end of their cycle. Most Overland garages still run the spring the door came with in the 1940s through 1960s. Cold snaps and freeze-thaw swings are when they snap.
- Heavy doors on detached workshops. Oversized or heavy shop doors get blamed on the opener. The real fault is a spring that stopped carrying the door’s weight.
- Low-clearance headers forcing improvised setups. When a standard high-lift won’t fit, wrong-sized springs and improvised torsion setups fail early. Cables and end bearing plates wear with them.
- Missing safety cables on extension springs. Older installs often skipped the containment cable. We add it so a break stays in the track.
Trusted Brands We Service in Overland
We work on the door and opener you already own, from a Craftsman opener bolted up decades ago to a modern Chamberlain. Of the eight leading brands we’re factory-familiar with, Clopay and Wayne Dalton come up often on Overland’s older doors, alongside Genie and LiftMaster openers. We diagnose the right part faster because we know the brand. Call (844) 745-3717 for a free estimate.
See the difference
Before
After
Before
After
Before
AfterPricing for Garage Door Spring Repair in Overland, MO
Our spring repair range in Overland is $180 – $340 for one spring. A matched pair is usually replaced together, so a pair costs about twice that range, and we’ll tell you which your door needs before quoting. Other common repairs on the same call:
| Service | Typical Estimated Range |
|---|---|
| Spring Repair (one spring) | $180 – $340 |
| Cable Repair | $130 – $250 |
| Garage Door Repair | $150 – $600 |
What moves the number: door weight, whether a cable or end bearing plate needs replacing, and whether a low-headroom kit has to be ordered for your header. The written estimate sets the final price, agreed before any work starts. Estimates are free.
We Also Serve Cities Near Overland
We take spring and door calls across the inner-ring suburbs around Overland, including St. Ann, University City, Bridgeton, and Clayton. Same mid-century housing stock, same low-clearance headers, same spring failures. Call (844) 745-3717 to book a free estimate.
Serving Overland, MO – Our Local Coverage Area
We serve Overland and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Garage Door Spring Repair in Overland
Yes. We service torsion and extension springs on the post-WWII brick and frame bungalows and small rentals common across Overland, including the older systems most generalists avoid. That covers original torsion setups, extension springs needing safety cables, and the sizing check for a low-clearance header. We answer 24/7, so call (844) 745-3717, and estimates are free.
Usually same day. Fast dispatch from 7am to 7pm, Sunday through Friday, gets a local pro to your door as soon as the schedule allows. We answer 24/7. Call (844) 745-3717 for timing and a free estimate.
Spring repair in Overland typically runs $180 – $340 for one spring. If the break took a cable with it, add $130 – $250 for cable repair. The written estimate sets the final price. Call (844) 745-3717 for an exact quote.
No. The price is quoted and agreed in writing before any work starts. If your low-clearance header needs a special-order kit, we’ll tell you and re-quote before we order it. Call (844) 745-3717 for a free estimate.
Yes. We serve addresses across Overland and the surrounding streets, including the older closes near Lackland and Woodson, and the surrounding suburbs. Call (844) 745-3717 to confirm availability for your address.
Spring Repair Done Right in Overland
Whether it’s a snapped torsion spring on a mid-century bungalow or a heavy shop door that won’t lift, we take the call. We’ll measure, rate the spring correctly, and give you a written price before anything starts. Call (844) 745-3717 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Florissant Garage Door Repair Pros.